Building a home golf simulator is one of those projects that sounds straightforward until you actually start planning it. Launch monitors, projectors, hitting mats… those are the fun parts. The real headache usually comes when you start asking a much more basic question:
How am I going to safely mount an impact screen in this room?
That’s where a golf simulator enclosure can make the entire process dramatically easier. Instead of trying to design a custom solution from scratch, an enclosure kit gives you a purpose-built frame, screen, and surround that are designed to work together.
In this review, I’m taking a detailed look at the SIG10 Golf Simulator Enclosure from the Indoor Golf Shop, based on my own hands-on experience assembling it and using it in a real home simulator space.
Table of Contents
- Why an Enclosure Makes Sense for Most Home Simulators
- Overview of the SIG10 Enclosure
- What Comes in the Box
- Assembly Experience: One Person, No Tools
- Installing the Nylon Surround
- Impact Screen Quality and Performance
- Edge Padding and Safety Design
- How the SIG10 Fits in a Real Room
- DIY Kit and Package Options
- Who the SIG10 Is Best For
- Final Verdict
Why an Enclosure Makes Sense for Most Home Simulators
Before getting into the SIG10 specifically, it’s worth explaining why enclosure kits are so popular.
If you go the DIY route, you’ll need to figure out:
- How to hang an impact screen safely
- How to tension it correctly
- How to protect walls, ceilings, and corners
- How to prevent dangerous ricochets
All of that is doable, but it takes time, planning, and trial and error. For many golfers, that’s enough friction to delay or completely derail the project.
An enclosure kit removes most of that guesswork. You get a proven design, known dimensions, and materials chosen specifically for simulator use. For me, realizing that kits like this existed was what finally pushed me to build a simulator at home.
Overview of the SIG10 Enclosure
The SIG lineup includes several enclosure sizes:
- SIG8
- SIG10
- SIG12
The number roughly refers to the width of the enclosure. This review focuses on the SIG10, which sits in a sweet spot for many garages and bonus rooms.
SIG10 Dimensions
- Width: 10 ft 10 in
- Height: 8 ft 4 in
- Depth: About 5 ft (not including optional side barrier netting)
The depth sometimes causes confusion because the product listing includes optional side netting that extends farther. Without that netting installed, the actual footprint into the room is much shorter and easier to work with.
What Comes in the Box
When the SIG10 arrives, everything needed to assemble the enclosure itself is included:
- Aluminum frame pipes
- Steel corner and connector pieces
- Impact screen
- Nylon surround (top and sides)
- Ball bungees
- Foam edge padding
- Instructions and QR codes for videos
Once the enclosure is built, you simply add:
- A hitting mat
- A launch monitor
- A projector
This modular approach lets you build the simulator in stages or customize each component to your budget and preferences.
Assembly Experience: One Person, No Tools
One of the standout features of the SIG enclosure system is the assembly process.
The aluminum pipes are:
- Lightweight
- Color-coded
- Equipped with push-button connectors
You match colors, slide the pipes together, and the buttons lock them in place. That’s it. No drilling, no bolts, no tools of any kind.
The entire enclosure can realistically be assembled by one person. I built mine solo, start to finish, without frustration or heavy lifting.
Frame Stability
At first, the lightweight pipes might raise an eyebrow. They feel almost too light when you’re holding them individually. But once the frame is fully assembled, it’s rock solid.
The key is that while the pipes are aluminum, all the connectors and corners are steel. That combination keeps the enclosure stable while making assembly much easier than heavier steel frames.
Once assembled, the enclosure does not shift or move when struck by high-speed shots. Or at least average speed shots (155mph)…
Installing the Nylon Surround
The surround material covers the top and sides of the enclosure. It’s thinner than what you’ll see on some other enclosures and feels similar to a bedsheet at first glance.
That initially gave me pause, but once installed, it makes a lot of sense.
The surround:
- Velcros around the front and bottom pipes
- Wraps around the back using bungee cords
- Gets stretched extremely tight
When tensioned evenly, wrinkles disappear and the finished look is very clean. The thin material actually helps here, because it doesn’t bunch up or sag once pulled tight.
Mishit Protection
Believe it or not, I’ve already hit shanks into the side of the enclosure. Instead of rebounding unpredictably, the ball hits the surround and gently drops down or rolls into the screen.
Even with only a few inches of clearance between the enclosure and the wall, the surround stays tight enough that the ball never contacts the wall behind it.
Impact Screen Quality and Performance
The impact screen is the heart of any simulator enclosure, and this is where performance matters most.
Projected Image Quality
With a projector running, the image looks excellent:
- Bright
- Sharp
- Consistent across the screen
It pairs well with popular simulator software and doesn’t introduce noticeable hotspots or distortion.
Bounceback Control
Bounceback is always a concern, especially with driver shots. The SIG screen uses ball bungees around the perimeter, allowing the screen to absorb impact rather than reflect it.
I installed every bungee and tested it that way. Bounceback has been very manageable. Balls typically drop straight down or roll back slowly, rather than shooting back toward the hitting area.
If needed, bounceback can be tuned by removing bungees, but so far that hasn’t been necessary.
Shipping Wrinkles
Like most impact screens, the SIG screen ships folded. When installed, some wrinkles are visible with the projector off.
Once the projector is on, they’re barely noticeable unless you’re actively looking for them. Based on other user experiences, these wrinkles tend to relax over time with use, heat, and repeated impacts.
Edge Padding and Safety Design
One of the most practical design elements of the SIG enclosure is the edge protection.
Foam padding runs along:
- The top
- Both sides
- The bottom
The padding is soft, thick, and covered in a felt-like material. It attaches with Velcro and fills the gap between the screen and the frame.
This does two important things:
- Protects the frame from direct impacts
- Prevents balls from sneaking behind the enclosure
So far, I haven’t had a single ball get behind the enclosure, even on bad mishits into the corners. From a safety standpoint, this is a big win, especially in tight rooms or garages.
How the SIG10 Fits in a Real Room
In my setup, the SIG10 fits almost wall-to-wall in a roughly 12-foot-wide space. I’m left with only a few inches of clearance on each side.
That’s about as tight as I’d recommend going, but it works. The enclosure feels like it was made for the space, and the finished look is clean and professional.
If you’re planning a simulator room, tools like the Indoor Golf Shop’s 3D Simulator Room Builder are extremely helpful. You can input your room dimensions and visualize exactly how the enclosure, projector, and launch monitor will fit before you buy anything.
DIY Kit and Package Options
If you want to save some money, the Indoor Golf Shop also offers a SIG DIY kit. This version includes:
- All connectors
- Screen
- Surround materials
You source and cut your own EMT pipe locally. It’s a good option if you’re comfortable with a bit more hands-on work.
They also offer complete simulator packages that bundle:
- A SIG enclosure
- Hitting mat
- Launch monitor
- Projector
Everything can be customized, which simplifies the buying process if you want a one-stop solution.
Who the SIG10 Is Best For
The SIG10 enclosure is an excellent choice if you:
- Want a straightforward, no-drama build
- Have a garage or spare room with limited space
- Value easy assembly and clean aesthetics
- Don’t want to fabricate a custom mounting solution
It’s especially appealing for golfers building their first simulator, because it removes a lot of uncertainty from the process.
Final Verdict
The SIG10 Golf Simulator Enclosure does exactly what it’s supposed to do: it makes building a home golf simulator easier, safer, and cleaner.
Assembly is quick and painless. The frame is stable. The screen performs well. The surround and padding handle mishits confidently. Once it’s up, it disappears into the background and lets you focus on playing golf.
If you’re on the fence about starting a simulator project, an enclosure like the SIG10 can be the piece that turns the idea into reality.
A full comparison with other popular enclosures is coming later, but standing on its own, the SIG10 is a strong, well-thought-out option that I’d feel comfortable recommending.
Read Next:
